+86 132 06063693

sales@acorefiltration.comsales@acorefiltration.com
Blog
Maintenance method of Lube Oil Purifier October 24,2019.

1. The Lube Oil Purifier that is running needs to interrupt the operation, the heating power supply should be disconnected for 5 minutes before the operation of the oil pump can be stopped to prevent the local oil in the oil path from being thermally decomposed to generate hydrocarbon gas.

 

2. After the outdoor low temperature environment is over, the vacuum pump must be drained to the condenser and the water in the cooling water tank to prevent the ice from damaging the equipment.

 

3. When the Lube Oil Purifier is not in use, the oil in the vacuum pump should be drained and new oil should be injected;

 

4. The condenser and heater of the Vacuum Lubricating Oil Purifier should be inspected regularly. The dirt collected in the condenser heat pipe can be purged with compressed air to prevent the heat exchange capacity from decreasing. If carbon is found on the surface of the heating element of the electric heater, the cause should be identified and eliminated to improve the heating efficiency of the heater.

 

The polluted oil enters the heater through the inlet under the action of external atmospheric vacuum suction. The heated oil enters the primary filter, and the large particle impurities are filtered out, and then the oil enters the vacuum separator and flows through the special third device. The diverging device creates a huge surface area per unit volume of oil, allowing the contaminated oil to be exposed to relatively low temperatures.

 

In the atmosphere, the water, air and gas in the oil are removed, and the mixed gas formed by the evaporated water vapor and the gas is condensed into a liquid through the water tank and the cooler, and enters the water reservoir together, and the remaining gas is vacuum-extracted. The oil that removes moisture is input into the fine filter by the oil discharge pump to remove particulate impurities, which is to purify the oil and complete a purification process.

 

Depending on the amount of water, multiple cycles are required to completely remove moisture.

The fine filter material with strong impurity filtering ability, large area and deep layer can remove fine particles in oil. Automatic backwash function, automatic cleaning of the filter, and a large amount of impurities trapped. Advanced media absorption condensing system. Lubricating oil filter unit is equipped with pressure protection, automatic temperature control heating, automatic separation of condensate device, drainage in online operation, operation

 

Simple, safe and reliable. It adopts high-quality filter material, has large dirt absorption, corrosion resistance, high temperature resistance and high mechanical strength. It has high impurity precision and long service life. Unique degassing and dehydration system; adopts three-dimensional evaporation technology and multi-layer oil-water separation technology to quickly separate moisture, gas and impurities in oil.

 

Lubricating Oil Purifier mainly deals with unqualified industrial oils such as mechanical oil, hydraulic oil, compressor oil and refrigeration oil. It can quickly and effectively remove moisture, gas, impurities and volatiles from oil, and restore the viscosity of oil. And use performance. The treated lubricating oil has low emulsifying value, very little water content and high impurity precision, which can be fully used at home and abroad.

 

It is re-used in high-precision hydraulic lubrication equipment and is suitable for purification and regeneration of various lubrications in petroleum, chemical, mining, metallurgy, electric power, transportation, machinery manufacturing, railway and other industries.

 

The components of the Lube Oil Purifier have been adjusted before leaving the factory. When transported to the site of use, it is necessary to check whether the parts are intact. The Lubricating Oil Purifier unit is placed smoothly, and the oil outlet is connected to the lower part of the fuel tank at the oil inlet, and the oil outlet is connected to the upper part of the oil tank. The Oil Purifier is connected to the power supply and ground wire. The power distribution cabinet and the oil pump, vacuum pump and heater wiring on the machine should be inspected.

 

Make sure the connection is secure and the insulation is reliable. The oil pump starts at the motor and observes whether it rotates clockwise. Otherwise, the power supply is changed in phase. When operating hydraulic oil and other mechanical oils online, it is necessary to properly replenish the same grade oil to ensure the oil level of the fuel tank is normal

Previous Post Next Post

Copyright © 2024 Acore Filtration Co. Ltd.

Request A Quote

Request A Quote